What size cut out do you require?
Answers
None, this is a surface mounting fitting so no hole cut out is required
I want to replace my ancient under-unit lights. There is one cable linking all 5 lights; it is of the correct length. So do I now have to find a way of neatly leading 5 cables under the units and also looking after the excess cabling?
Answers
Yes each light comes with its own cable which needs to go back to the driver
Replacement led bulbs and drivers
Do you have to replace the whole unit when the bulb fails or can the bulbs be replaced and if so where do you buy them? How long do the drivers last without having to be replaced?
Answers
Yes the whole unit needs to be replaced. The drivers are guaranteed for 3 years
Good Morning. I need 6 of these lights but 2 will need to be more than 1.5m from the driver. It looks like they fix into the driver with a specific connector which wouldn't therefore allow extending the cable. Is it possible to get some sort of intermediate extension cable which could connect into the light and the driver. If not I presume I could get a couple of the 3 light kits and make use of the longer mains cable. Thanks
Answers
You can use this extension cable, you would need the JB version https://www.lightsupplier.co.uk/led-extension-cable-for-led-downlights-1-5/
Hello! I’m having 2 cabinets installed and want 2 x lights on each. The wiring is in place. Do I need one driver per wire so 4 lights and 2 drivers?
Answers
Hi Yes you would need two 8 Watt LED drivers - SY9980
I want to replace my existing 4 lights with this product. Should I purchase the 6 lights + driver or should i purchase 2 sets of 3 + drivers. How much cabling does this product come with ? Thanks
Answers
You can purchase 4 single lights and 1 x 20 Watt LED Driver - Product Code: SY7350
Are these suitable to be fixed at the top of a glass fronted kitchen cabinet. My main question is- do they emit enough light to be suitable for this purpose? Thanks!
Answers
Yes they are fine for glass fronted cabinet
I am buying 3 of these lights to go under one row of units on the same wall. What do i need to buy to instal them?
Answers
You would need a 8 Watt LED Driver Product Code - SY9980
I require 7 lights to be connected to one another and controlled together - Should i be purchasing a port for 6 and then a separate bulb for the 7th light?
Answers
You would need 1 x 6 light kit, 1 x single light and 1 x 8 Watt LED Driver. Each light will need to go back to the driver. A maximum of 6 lights can be run off one driver
do you have a port for more connections as i may need more than 6 lights
Answers
unfortunately 6 light lights per driver is the maximum
do you have a port for more connections as i may need more than 6 lights
Answers
unfortunately 6 lights per driver is the maximum
MAXIMUM LIGHTS PER DRIVER
What is the maximum number of lights you can have per driver?
Answers
The maximum number of lights per driver is 3 on the 8 Watt version and 6 on the 20 watt version
Hi there, I’m currently building a studio, which is soundproof and don’t which to make loads of holes in the plasterboard for traditional Down lighters for obvious reasons. Would these work as ceiling lights and would a pack of 6 be sufficient to light a 2.5m x 3.5m room? I assume I just cable above the ceiling as per traditional lighting? Many thanks for your assistance in advance. Kind regards Rob
Answers
No these would not be suitable as a LED ceiling light as the light output would be too low.
which driver and do I need two?
Hello, I want to purchase 3 of these lights two will sit in cabinets on one side of a kitchen and the other 1 on the other side. Do I need two drivers? or can I buy a 3 x kit with one driver? and if I need two what sizes specs do I need? thank you
Answers
You would need the 8 Watt LED Driver - 3 Way Port for two lights
Dimming - ensuring compatibility
I want to dim 6 of these using a leading edge BG rotary light switch. Which driver will I need and will it have the same connector types as the lights?
Answers
The 30 Watt Dimmable LED Driver https://www.lightsupplier.co.uk/25-watt-dimmable-led-driver-with-6-way-port/
Do they need a cutout? if so, what dimensions?
Answers
These light fittings do not require a cut out.
Hi - is there are anyway this light can be attached to non metallic surfaces?
Answers
The base screws the the underside of the cabinet, the light then magnetically attaches to the base. So you can attach the light to any surface
Is this a plug in if not do you have any that do plug in Thanks
Answers
Yes this fitting has a J plug to go into the driver
I wish to replace existing round 12v halogen lights. Will these be suitable?
Answers
Yes they will be fine, but you will need to replace you halogen transformers to LED drivers